Real World Gigabit Ethernet and Wireless Througput

I was about to write about this and then I found a Netapp KB that explains it so here it is.


During the course of performance benchmarking, the issue of maximum theoretical throughput often rears its ugly head. What is the theoretical maximum for 1Gbps?

Note: The following are approximations that should be used as a guideline, and not as a scientific fact.

We know a couple of things about Ethernet that will allow us to calculate the theoretical maximum throughput. All frames must have a 8byte preamble, a 12byte inter-frame gap, and a minimum length of 64 bytes which includes Destination MAC (6 Bytes), Source MAC(6 Bytes), Protocol Type (2Bytes), Payload (46 Bytes) and CRC(4 Bytes). Given this, the frame size including the preamble and inter-frame gap is 84bytes (8+12+64).

The number of frames per second can be calculated as:

Rate / Frame size = frames per second

1000Mbps / (84bytes x 8) = frames/s


1,000,000,000 bits / 672 bits = 1,488,000 frames/s.

As a result, the maximum theoretical throughput is calculated as:

frames per second x frame size
1,488,000 x 512 bits** = 761Mbps

Note: 64byte frame x 8 bits = 512bits

However, we also lose some bandwidth from the preamble and the inter-frame gap. They can be calculated as follows:

Preamble (recall that it is 8bytes):
frames per second x 8 bytes x 8 bits (to convert it to Mbps)
1,488,000 x 8 x 8 = 95Mbps

Inter-frame gap (recall that it is 12bytes):
frames per second x 12 bytes x 8 bits (to convert to Mbps)
1,488,000 x 12 x 8 = 143Mbps

So the actual maximum, given 64 byte frames, is 523Mbps (761 – 95 – 143) or 65MB/s.

Now, let’s do the calculation quickly using a 1518byte frame.

Add in the preamble and the inter-frame gap:
8+12+1518= 1538
1000Mbps / (1538bytes x 8) = 81,274 frames/s
81,274frames/s x 12144bits*** = 986Mbps

Note: 1518bytes x 8 bits = 12,144bits

Preamble overhead: 81,274 x 8 x 8 = 5Mbps
Inter-frame gap overhead: 81,274 x 12 x 8 = 7Mbps

So the max throughput, given a 1518 byte frames, is 974Mbps (986 – 5 – 7) or 121MB/s.

Note that these numbers do not include Ethernet frame, IP, TCP or UDP overhead, so we will take an additional hit there.

Let’s take a look at a 9k MTU (jumbo frames) with all accompanying overhead for TCP.

Frame size = 9000bytes
Inter-frame gap=12bytes
Ethernet Preamble=8bytes
Ethernet Header=14bytes
Ethernet FCS=4bytes
IP Header = 20bytes
TCP Header = 20bytes
TCP Options = 12 bytes

Frames per second:
9000+12+8 = 9020 x 8 = 72,160 bits
1,000,000,000 bits / 72,160 bits = 13,858 frames/s

Max throughput with no overhead:
13,858 x 72,000 = 997Mbps

Preamble overhead:
13,858 x 8 x 8 = .886

Inter-frame gap:
13,858 x 12 x 8 = 1.33Mbps

Ethernet Header overhead:
13,858 x 14 x 8 = 1.55Mbps

Ethernet first customer ship (FCS) overhead:
13,858 x 4 x 8 = .443Mbps

IP Header overhead:
13,858 x 20 x 8 = 2.21Mbps

TCP Header overhead:
13,858 x 20 x 8 = 2.21Mbps

TCP Options overhead:
13,858 x 12 x 8 = 1.33Mbps

Theoretical throughput of Gigabit Ethernet with jumbo frames, and using TCP:
997Mbps – .886 – 1.33 – 1.55 – .443 – 2.21 – 2.21 – 1.33 = 987Mbps or 123MB/s.

The approximate throughput for Gigabit Ethernet without jumbo frames and using TCP is around 928Mbps or 116MB/s. However, this is still not an accurate representation of what your customer can expect in the real world. Other factors will influence the throughput. These include, but are not limited to, file sizes, types of transactions, cache hits/misses, cpu utilization, network utilization, disk utilization, protocol (Network File System (NFS), Common Internet File System protocol (CIFS), etc), client type, kernel version, etc.


So what does all this mean? Basically there are so many variables that it’s hard to tell you specifically what speeds you’ll get. But it’s guaranteed you’re not going to get the full 1G. Try explaining that to management.

The same holds true for wireless speeds.  Below is a table for N but again, you will not get those exact speeds.

Antennas (Tx*Rx) Spatial Streams Maximum Link Speed Band Support
N (b,g) Single Stream 1×1 1 72 Mbps 2.4
N (b,g) Dual Stream Dual Stream 1×2 2 150 Mbps 2.4
N (b,g) Dual Stream Dual Stream 2×2 2 150 Mbps 2.4
N (b,g) Dual Stream Dual Stream 2×3 2 150 Mbps 2.4
N (a,b,g) Dual Stream Dual Stream 2×2 2 300 Mbps 2.4 & 5
N (a,b,g) Dual Stream Dual Stream 2×3 2 300 Mbps 2.4 & 5
N (a,b,g) Multi-Stream Dual Stream 3×3 3 450 Mbps 2.4 & 5
More Stories
CTRL+ALT+DEL in a RDP Session